Page of 4 Next ››
    High Performance
  • Air Cleaner and Carb Set_image

    Air Cleaner and Carb Set

    A generic 14" x 3" round open element air cleaner with realistic pleat detail and top contours. It matches the look of aftermarket air cleaners sold through Jeg's or Summit. The inside is machined so it will fit low over our Holley 4150 Series carb for hood clearance. Includes one air cleaner and one carb in white resin.

    $5.00
  • Battery Box, Trunk Mount, Pair_image

    Battery Box, Trunk Mount, Pair

    Properly executed trunk-mount battery applications use a marine battery box like this to collect fumes and vent them outside the interior. These are commonly seen on street machines, street rods and drag cars. Many drag cars have two of these for extra weight at the rear. The universal battery box includes several locations to locate the ground and "B+" wires.

    $3.00
  • Battery Set_image

    Battery Set

    Upgraded! The Calnaga Battery Set now includes a trunk mount battery box and the Optima Spiral Cell AGM. These batteries are square, complete, and have detail that isn't possible with the injection molding process. Check the top post detail and side terminals. Six different batteries are included in the set: Universal maintenance-free battery, universal heavy duty battery, Autolite Sta-ful, a small 12-volt for OEM compacts and tuners, the battery box, and the spiral cell.

    $7.00
  • Battery, Spiral Cel, Group 34/78, pair_image

    Battery, Spiral Cel, Group 34/78, pair

    Optima spiral cel AGM batteries are the hot setup these days. This battery has label detail and accurate dimensions for the Group 34/78 size. The terminals will fit through common photo-etch battery cable clamps. Paint with a red top for hard starting drag race applications, and yellow top for race cars or street machines. Blue is for marine applications.

    $3.00
  • Blower Drive Pulley Set_image

    Blower Drive Pulley Set

    These blower pulleys were mastered in true machined aluminum and the realism exceeds other cast or machined offerings. The teeth are square and accurate for 1/2" pitch pulleys. Diameters represent a typical 40% overdrive. The idler has delicate, in-scale flanges. All of the pulleys have a pilot hole cast in at the center and material on the back side to facilitate drilling and pinning to your blower and engine block.

    $7.00
  • Blower Kit, Big Block_image

    Blower Kit, Big Block

    Add this excellent blower kit to your drag or radical street big block engine. Calnaga's exclusive blower manifold has much more realism than a kit part. Note the support structure and blow off plate. It has room for the distributor behind the blower and coolant fittings if needed. Modeled after a magnesium Cragar blower manifold and beautifully matched with Calnaga's 6-71 blower and Enderle 80's scoop.

    $7.00
  • Blower Manifold, Small Block Chevy_image

    Blower Manifold, Small Block Chevy

    This blower manifold has all the correct runner detail and gusseting. A lot more realistic than the typical trapezoid shaped piece of styrene you get in a kit. An excellent choice for diorama detail or if your engine is displayed with the valve covers off.

    $3.50
  • Blower Scoop Set_image

    Blower Scoop Set

    Three decades of blower induction in one convenient set. Hilborn 4 port scoop, Hilborn butterfly scoop, Enderle bug catcher -70's, Crower 8 port injector, and Enderle scoop, 80's style. And if that's not enough, you get a Hilborn 4 port injector with and without flange. The 4 port scoop fits the 4 port injector with flange perfectly. This is a fantastic deal, better than 50% savings over buying them. individually.

    $9.00
  • Blower Scoop, Crower 8-Port Injector_image

    Blower Scoop, Crower 8-Port Injector

    The Crower 8-Port injector was introduced in 1968, but really gained prominence on Don Garlits' first rear-engine dragster in 1971. This injector was tricky to tune but found success with various teams along with Garlits including Don Prudhomme, Keeling and Clayton, "Jungle Jim" Liberman, Gordie Bonnin, and Gene Conway. It's a prominent detail you need to get right if building a replica. If you are doing a ficticious drag subject from the Seventies into the early Eighties, it will add some unique visual interest.

    $3.00
  • Blower Scoop, Crower Four Butterfly_image

    Blower Scoop, Crower Four Butterfly

    The Crower blower scoop has four inlet butterflies and the Crower logo cast into the top. It's a little longer and lower profile than the more common Enderle scoop. It isn't too common, but it is pretty cool. Garlits ran one for a brief period. Calnaga took a kit part and fixed it by increasing the height, re-drilling the inlet ports and adding butterfly shaft detail.

    $3.00
HomeOur MissionAbout UsStoreGalleryNewsPoliciesContact Us

Calnaga Castings
The Calnaga Store