Page of 10 Next ››
  • 4x4 Front Axle Kit

    You'll have tremendous design flexibility with Calnaga's 4x4 Axle Kit. You get accurate axle ends, radius rods, Dana 44 differential, and an ample length of axle tube. Locate the differential left, right, or wherever you need it! Adjust the wheelbase, radius rod width, and pinion angle to suit your project. Have fun scratch-building, not head-scratching.

  • 4x4 Radius Rods (Set of 2)

    The design of these radius rods is loosely based on a full scale Ford Econoline 4x4 conversion known as a Quadravan. They are drilled to accept 0.125 tube or rod, so you can combine them with our 4x4 Front Axle Ends and the Dana 44 Differential to make a super-detailed front axle that fits your 4x4 just right.. They have a coil spring mounting pad and bolt head detail.

  • Accessory Display Set

    Add interest and realism to your display or diorama with Calnaga Display Accessories. These items are commonly found in the garage, pit area, or campsite. Put them in the back of your truck or van for a realistic load. The set includes one of each: Sleeping Bag, Bed Roll, Large Gear Bag, Small Gear Bag, and Fuel Jug 10 gallon (1:25 scale). (Parts shown include a paint and detail suggestion only. Your parts are delivered in plain white resin.)

  • Akront Rims, 1:12 Scale

    Akront aluminum rims include a tall rib on both sides for strength. They were popular on dirt bikes, street bikes and even some dragsters in the 60's and 70's. These are 1:12 scale replicas cast in high strength resin from machined aluminum masters. They include pilot holes for 36 spokes, valve stem, and rim locks. There is a groove around the outside diameter for spoke lacing wire. Includes two rims representing an 18" rear and 21" front. (Actual dimensions: 1.550" and 1.820" O.D.). For advanced modelers only. Calnaga will not be responsible for poor quality or frustration resulting from attempts to create scale spoked wheels with these rims.

  • Battery Box, Trunk Mount, Pair

    Properly executed trunk-mount battery applications use a marine battery box like this to collect fumes and vent them outside the interior. These are commonly seen on street machines, street rods and drag cars. Many drag cars have two of these for extra weight at the rear. The universal battery box includes several locations to locate the ground and "B+" wires.

  • Battery Set

    The problem with kit batteries is that they are injection molded, so they have that unrealistic taper called draft angle. Usually, they are hollow and don't even have six sides! These batteries are square, complete, and have detail that isn't possible with the injection molding process. Check the top post detail and side terminals. Four different batteries are included in the set: Universal maintenance-free battery, universal heavy duty battery, Autolite Sta-ful, and a small car battery for OEM compacts and tuners.

  • Battery, Spiral Cel, Group 34/78, pair

    Optima spiral cel AGM batteries are the hot setup these days. This battery has label detail and accurate dimensions for the Group 34/78 size. The terminals will fit through common photo-etch battery cable clamps. Paint with a red top for hard starting drag race applications, and yellow top for race cars or street machines. Blue is for marine applications.

  • Blower Manifold, Small Block Chevy

    This blower manifold has all the correct runner detail and gusseting. A lot more realistic than the typical trapezoid shaped piece of styrene you get in a kit. An excellent choice for diorama detail or if your engine is displayed with the valve covers off.

  • Blower Scoop Set

    Three decades of blower induction in one convenient set. Hilborn 4 port scoop, Hilborn butterfly scoop, Enderle bug catcher -70's, Crower 8 port injector, and Enderle scoop, 80's style. And if that's not enough, you get a Hilborn 4 port injector with and without flange. The 4 port scoop fits the 4 port injector with flange perfectly. This is a fantastic deal, better than 60% savings over buying them. individually.

  • Blower Scoop, Crower 8-Port Injector

    The Crower 8-Port injector was introduced in 1968, but really gained prominence on Don Garlits' first rear-engine dragster in 1971. This injector was tricky to tune but found success with various teams along with Garlits including Don Prudhomme, Keeling and Clayton, "Jungle Jim" Liberman, Gordie Bonnin, and Gene Conway. It's a prominent detail you need to get right if building a replica. If you are doing a ficticious drag subject from the Seventies into the early Eighties, it will add some unique visual interest.

HomeOur MissionAbout UsStoreGalleryNewsPoliciesContact Us

Calnaga Castings
The Calnaga Store